Quick-action ceiling anchor W-DS/S With hooks
Quick ceiling anchor W-DS/S
ANC-(W-DS/S)-(A2K)-6X75
Register now and access more than 125,000 products
- Quick and easy to install
- Less drilling effort
- No special drill or setting tool required
- Simple insertion process: Insert by hand, pull down sharply – done
- Anchorage via friction locking – controlled expansion anchor
Multiple attachment of non-load-bearing systems in concrete: European Technical Approval ETA-13/0490
- Dimensioning in accordance with the “Guideline for European Technical Approval (ETAG) for metal anchors in concrete” Appendix C, Dimensioning method C
- The anchor has European Technical Approval for use in reinforced or non-reinforced standard concrete with a strength class of min. C20/25 and max. C50/60 in accordance with EN 206-1:2000-12.
- Multiple attachment of non-load-bearing systems; Anchorage with European Technical Approval in cracked concrete (tension zone) and non-cracked concrete (compression zone)
Create the drill hole
Clean the drill hole
INSERT W-DS/S.
Fully insert W-DS/S.
Pull down the W-DS/S with a jerky movement.
Multiple attachment of non-load-bearing systems in concrete: European Technical Approval ETA-13/0490
- Dimensioning in accordance with the “Guideline for European Technical Approval (ETAG) for metal anchors in concrete” Appendix C, Dimensioning method C
- The anchor has European Technical Approval for use in reinforced or non-reinforced standard concrete with a strength class of min. C20/25 and max. C50/60 in accordance with EN 206-1:2000-12.
- Multiple attachment of non-load-bearing systems; Anchorage with European Technical Approval in cracked concrete (tension zone) and non-cracked concrete (compression zone)
Datasheets(X)
- Suitable for attaching: Lightweight ceiling coverings and false ceilings, ceiling substructures with wire hook, wire hanger, Vernier hangers, light strips, luminaire carrier rails, lamps, cables, chains etc.
- The anchor can be used only in dry indoor areas
null | null |
| Anchor diameter [mm] | 6 | |
| Anchors in a redundant non-structural system in non-load-bearing systems in concrete (for all load directions) | Fadm [kN] ≥ C20/25 and ≤ C50/601) | 0,5 |
| Würth system components (see 33.1 W-DN) 1) The partial safety factors of the resistances regulated in the approval and a partial safety factor of the actions of γF = 1.4 have been taken into account. Please refer to the European Technical Approval Guidelines (ETAG), Annex C, for information on combining tensile and transverse loads, influence of the edge distance and groups of anchors. | ||
| Minimum spacing | smin [mm] | 200 |
| Minimum edge distance | cmin [mm] | 100 |
| Minimum member thickness | hmin [mm] | 80 |
| Effective anchorage depth | hef [mm] | 33 |
| Nominal drill diameter 2) | d0 [mm] | 6 |
| Diameter of cutting edges2) | dcut ≤ [mm] | 6,4 |
| Drill hole depth | h1 ≥ [mm] | 40 |
| Würth system components (see 33.1 W-DN) 2) Tungsten carbide hammer drill bits must comply with the specifications set out in the information leaflet of the Deutsches Institut für Bautechnik (German Institute of Civil Engineering - DIBt) and the Association of German Tool Manufacturers (FWI) on the "characteristic values, requirements and tests for masonry drill bits with tungsten carbide cutting body which are used for making drill holes for anchoring". Würth hammer drill bits meet the specifications set out in the information leaflet. | ||
Last viewed
Metric combination wrench with POWERDRIV®
Hose set For TOP Gun cleaning and washing appliances
Power spray glue plus
Drawer For workshop trolleys
Carro 3 MOTION WÜRTH
Pan Head screw with hexalobular head ISO 14583, steel 10.9, zinc-plated, blue passivated (A2K)
Bond + Seal structural adhesive
Hard hat SH 2000-S
Interior sliding door fitting VIDRO 101-H
Handle For cleaning brushes