Plastic frame anchor W-UR 6 SymCon^®

Name: Plastic frame anchor W-UR 6 SymCon ®
Brand: Würth
SKU: 0912806403

Plastic frame anchor, W-UR 6 SymCon, cntrsnk. head
ANC-(W-UR SYM)-PLA-AW20-(A2K)-30-6X80
ZEBRA

Art.-no. 0912806403

EAN 4050642732803

All versions

Specification

The first 6-series plastic anchor with ETA for multiple attachment in concrete. With pre-assembled countersunk head screw made of zinc plated steel

Reliable post-spreading characteristics

Enabled by geometry of the SymCon plug screw

Increased load introduction

Screwing in the SymCon screw results in optimum compression of the plastic of the wall plug body (almost no back-cut)

Improved load transfer

Even, continuous load distribution across the entire expansion area

Low assembly workload

Pre-assembled wall plug body and special screw

The hammer-in stop prevents premature expansion of the anchor during installation

Anchorage via friction locking between wall plug body and anchoring base

The wall plug body is made of high-quality polyamide

Proof of Performance

W-UR 6 SymCon and W-UR F 6 SymCon (galvanised steel): European Technical Approval ETA-11/0309.

The anchor has European Technical Approval for use in multiple attachment of non-load-bearing systems (e.g. suspended ceilings etc.).

Anchoring bases without approval: Solid brick, solid sand-lime brick, vertically perforated brick, hollow sand-lime brick, hollow lightweight concrete blocks, solid bricks and blocks made of lightweight concrete

Installation temperatures: Temperature of anchoring base:≥ –20°C Temperature of wall plug body:≥ 0°C

Notice

Drill cuttings must be removed from the drill hole.

Application area

Create the drill hole

Clean the drill hole

Set anchor and screw

Screw in the screw

Screw in screw until flush

W-UR 6 SymCon and W-UR F 6 SymCon (galvanised steel): European Technical Approval ETA-11/0309.

The anchor has European Technical Approval for use in multiple attachment of non-load-bearing systems (e.g. suspended ceilings etc.).

Anchoring bases without approval: Solid brick, solid sand-lime brick, vertically perforated brick, hollow sand-lime brick, hollow lightweight concrete blocks, solid bricks and blocks made of lightweight concrete

Installation temperatures: Temperature of anchoring base:≥ –20°C Temperature of wall plug body:≥ 0°C

Application area

Suitable for attaching ceiling substructures (made of wood or steel), wooden laths, metal rails, suspended ceilings, angle brackets, profiles etc.

Anchor diameter	6 mm
Anchor length (l)	80 mm
Nominal drill-bit diameter (d 0)	6 mm
Through-hole in the component to be connected (d f)	6.5 mm
Material of screw	Steel
Internal drive	AW20
Surface of the screw	Zinc plated
Drill hole depth (h 1)	60 mm
Approval	ETA-11/0309
Type description	W-UR 6 SymCon, countersunk head screw

Performance data: Concrete, multiple attachment of non-load-bearing systems
Anchor diameter		[mm]	W-UR 6 SymCon
Embedment depth of the anchor sleeve		h_nom[mm]	50
Centric tension load¹⁾ for individual anchors or an anchor group	N_perm = C12/15 [kN]	30°C²⁾/50°C³⁾	0,79
	N_perm ≥ C16/20 [kN]	30°C²⁾/50°C³⁾	0,79
Shear load¹⁾ for individual anchors or an anchor group	V_perm	[kN]	2,05
Minimum member thickness	h_min	[mm]	90
Minimum axis distance⁴⁾	s_min [mm]	C12/15	60
Minimum axis distance⁴⁾	s_min [mm]	≥ C16/20	40
Minimum edge distance⁴⁾	c_min [mm]	C12/15	60
Minimum edge distance⁴⁾	c_min [mm]	≥ C16/20	40
Characteristic edge distance	c_cr,N [mm]	C12/15	60
Characteristic edge distance	c_cr,N [mm]	≥ C16/20	40
¹⁾ The partial safety factors of the resistances regulated in the approval and a partial safety factor of the effects of γ_F = 1.4 have been taken into account. For the combination of tensile and transverse loads, please refer to ETAG 020 Appendix C. ²⁾ Maximum long-term temperature. ³⁾ Maximum short-term temperature. ⁴⁾ The permissible load must be reduced.

Installation parameters: Concrete
Anchor diameter [mm]		W-UR 6 SymCon
Nominal drill diameter	d₀ [mm]	6
Drill cutting dia.	d_cut ≤ [mm]	6,4
Drill hole depth	h₁ ≥ [mm]	60
Embedment depth of the anchor sleeve	h_nom [mm]	50
Through hole in the attachment	d_f ≤ [mm]	6,5