Pipe sleeve type RK I
Pipe sleeve, type RK I
PIPSLEV-M-250MM
Art.-no. 0893304250
EAN 4045989948215
Register now and access more than 125,000 products
- Synthetic rubber insulated pipes (insulation ≤ 43 mm) up to 250 mm in diameter can be routed through the sleeve
- Space-saving installation thanks to low sleeve height
- Can be installed in extremely tight spaces
- No loose fastening parts
- No pre-assembly
- Few fixing points
- Additional acoustic insulation possible
- Can even be used at high temperatures
- Moisture does not impair functionality
- Control cables for pneumatic tube transport systems may be routed through
- Solid foam withstands the pressure of firefighting water
- Zero spacing between sleeves permissible
- Entirely maintenance-free
- Extremely easy to use
- Can be reused after removal
Wall and ceiling ducts fire-resistant Z-19.53-2349
- Select the correct sleeve for the outside diameter of the pipe being protected
- In difficult installation situations, a sleeve up to three sizes larger can also be selected (applies up to a pipe outside diameter of 110 mm)
- The sleeve (up to a sleeve diameter of 200 mm) can be mortared into position without using an anchor by bending the retaining brackets
| The following dimensions must be observed when installing the fire protection sleeve: | |||||
| External diameter of plastic pipe from 32 to 315 mm. | |||||
| Cuff diameter mm | ≤ 200 | > 200–≤280 | > 280–≤315 | ≤ 280 | > 280–≤315 |
| Minimum thickness of component for | Wall bulkhead R 90 | Ceiling bulkhead R 90 | |||
| Masonry according to DIN 1053-1 | 100 mm | 150 mm | 200 mm | – | – |
| Concrete, reinforced concrete according to DIN 1045 | 100 mm | 150 mm | 200 mm | 150 mm | 200 mm |
| Light partition walls in accordance with DIN 4102 | 100 mm | – | – | – | – |
Close the remaining gap between the plastic pipe and the reveal. Place the folded boot around the plastic tube.
WÜTOP sleeve Attach the cuff with a dowels or screw in the bent tabs.
Affix ID plate
Wall and ceiling ducts fire-resistant Z-19.53-2349
Datasheets(X)
For use in systems <[A]/> + <[C3]/> + <[F]/>
- Combi partition <[A]/> combi AB soft partition <[C3]/> fire protection sleeve <[F]/>
- For wall and ceiling ducts
Fire rating of 90 minutes, fire resistant - For combustible pipes with an outer diameter up to 315 mm
For multi-layer composite pipes and pipe systems with protective pipe (double pipe system) - For pneumatic tube transport systems and vacuum cleaner lines
- For masonry and concrete ceilings and walls; also for light partition walls
For fire-resistant walls from 100 mm: One sleeve on each side of the wall - For fire-resistant ceilings from 150 mm: One sleeve on the ceiling underside
- Approval also permits partitioning of beverage hoses
DN nominal width | DN 250 |
Internal diameter | 256 mm |
Outer diameter | 336 mm |
Height | 60.0 mm |
Select RAL-colour code
!! NOTE: On-screen visualisation of the colour differs from real colour shade!!
Last viewed
Hexagon socket set screw with pin ISO 4028, A2 stainless steel, 21H, plain
Screwdriver handle with hex bolster
Screwdriver slotted striking cap with hexagon shank
Hole puncher assortment 12 pieces with manual hydraulic punch
Allen key, hexagon socket with ball head extra-long version
1/4 inch socket wrench insert, metric short
Cover caps for aluminium airline lashing rails
Windscreen cleaner with anti-freeze protection down to -10 °C
1/2-inch impact socket wrench insert hexagon, metric, long
Thread mandrel with nozzle