MASTERKOL C2 TE S1
Tile adhesive MASTERKOL
ADH-TLE-(MASTERKOL-C2-T)-GREY-25KG
Register now and access more than 125,000 products
- Excellent initial adhesion and maximum adhesion after 28 days.
- Suitable for vertical and horizontal surfaces.
- Sufficient elasticity to absorb small movements between the tiles and the base.
- Resistant to industrial environments.
- Does not age when exposed to the elements.
- Perfectly resists immersion in water and thermal changes.
- C2 TE S1 EN-12.004 classification
- Does not sag.
Amount used
- On smooth surfaces: from 2 to 3 kg/m².
- On plaster: from 3 to 3.5 kg/m².
- For double bonding: from 5 to 6 kg/m².
Storage:
For 12 months from date of manufacture. In its original sealed container, stored in a cool, dry place. Protect from light, frost and excessive heat.
Datasheets(X)
• Laying stoneware, porcelain stoneware, natural stone on mortar or plaster substrates.
• Exterior façades and pavements.
• Kitchens, bathrooms, toilets, patios and interiors in general.
• Swimming pools and water tanks on mortar where the substrate has not been waterproofed.
• Underfloor heating.
• Ideal for high traffic areas: airports, supermarkets, industry, hospitals etc.
• Substrates must always be strong, solid, and free from dust, paint, wax and oil.
• Mix 6 litres of water per 25 kg bag.
• Mix with an electric beater to a smooth, lump-free paste.
• Let stand for 2 minutes and mix again before applying.
• Spread the paste with a toothed trowel with teeth sized according to size of the ceramic tiles to be laid. Spread the paste in sections not exceeding 2 m² and comb it with the toothed trowel in a straight line, perpendicular to an edge of the tile and before laying the tiles: the less time taken between combing the paste and laying the tile, the better the adhesion will be. Then, firm up all the tiles by tapping them with a rubber club hammer.
• Tiles can still be worked on up to 30 minutes after spreading the paste.
• Min. application temperature 5°C and max. 35°C.
• It can totally withstand traffic for grouting after 24 hours.
It is essential to follow the specifications of Chapter 7.4. of the EN 138.002 standard when laying on façades. Use the double bonding technique. If the tiles are larger than 30 x 30 cm, use stainless steel metal anchors as well.
Weight of content | 25 kg |
Chemical basis | Cement |
Standards | EN 12004 |
Colour | Grey |
Min./max. processing temperature | 5 to 35 °C |
Processing time | 60 min |
Application conditions | dry surface |
Min./max. open time /conditions | 30-60 min / at 20°C |
May be walked on after max. | 24 h |
May be walked on in following conditions | once completely dry |
Groutable after | 24 h |
Grouting condition | at 20°C and 65% relative humidity |
Full load capacity/conditions | 48 h / at 20°C and 50% relative humidity |
Shelf life from production/conditions | 12 Month / at 10°C to 25°C |
Last viewed
Window frame screw AMO® III type 1
Collated nails and gas cartridge NG CS-2/3 HFB
Comb nail / anchor nail
Safety boots S3 SCARPA ALTA STEEL
Jigsaw blade, construction, three stars For gypsum plasterboard and fibre cement
Multiclean cleaning liquid
Aluminium mobile scaffolding 1.58 m - module 1
Hexagonal nut with flange and clamping piece (all-metal) according to MBN standard
Würth MODYF high-visibility work fleece
Booster LB 1000 12 V Li-ion jump starter