Elastic waterproofing coating RECUFLEXIM
Elastic waterproof coating RECUFLEXIM
SFRCOAT-WATERPROOF-WHITE-25KG
Register now and access more than 125,000 products
- Waterproof and non-breathable.
- Excellent adhesion to properly prepared substrates.
- Ageing- and weather-resistant.
- Excellent flexibility, even at extreme temperatures (-10°C to 80°C).
- Absorbs expansion and movement.
- Stable colour spectrum.
- Fungicide and anti-mould.
- Easy to apply.
- Ready for use.
- Non-toxic and self-extinguishing.
Coating not suitable for regular foot traffic. Do not apply the product in adverse weather conditions such as rain, snow etc.
On horizontal surfaces or surfaces with inclines less than 3 %, where there is a possibility of water pooling, or in environments of excessive and continuous sun, cold, snow exposure etc., we advise applying a coat of RECULASTIC.
These instructions are merely recommendations based on our experience. We recommend performing tests for each new type of application or surface to be treated.
Datasheets(X)
For waterproofing both new and renovated porous tiles; fibre cement roofs, after treating the degraded parts with RECUPRIMER art. no. 0893199800; bituminous asphalt sheets; and PE or PU insulation materials.
Protection against rainwater, unpressurised moisture and leaks both horizontally and vertically.
Waterproofing and sealing fissures, cracks and joints.
Substrates must be clean and dry, free from particles and grease. For non-porous or non-absorbent media, we recommend using Recuprimer art. no. 0893199800. Apply with roller, brush or airless spray gun (in this case thin with 20 % water and apply a minimum of three coats) on the surface to be treated. Apply between two and three coats. If applying three coats, use fibreglass mesh between the first two coats.
Consumption
As a guideline, the amount used per coat when applied vertically can range from 0.35 to 0.40 kg/m2. This amount is between 0.75 and 1.00 kg/m2 when applied horizontally.
Chemical basis | Natural rubber |
Colour | White |
Min. processing temperature | 5.0 °C |
Max. processing temperature | 40.0 °C |
Shelf life from production | 12 Month |
| Technical data | |
| Composition | Saturated polyesters in dispersion |
| Density | 1.30 ± 0.01 g/cm³ |
| Appearance | High viscosity paint |
| Viscosity | 6000 cP |
| Type of thinner | Water |
| Elongation at break | > 280 % |
| Solid content | 58 % |
| Application temperature | Between 5°C and 40°C |
| Dry to touch | Approx. 1 hour |
| Completely dry | Between 2 and 4 hours |
| Paintable | Between 4 and 6 hours |
| Ready to bear a load | 24 hours |
| Temperature resistance | From -10°C to +80°C |
| Storage | 12 months in its original sealed container, stored in a cool, dry place. At temperatures between 5°C and 40°C |
| VOC content 2004/42 Cat II A (i) 140 g/L. Max. VOCs: 7 g/L. | |
Last viewed
3/8" socket wrench insert Inch, hexagon, short
Extra flat head pias screw ZEBRA
Acid detergent ACIDODET
Würth MODYF high-visibility work fleece
Universal holder Ø 7 mm With quick-change chuck
Burr heads with 1/4" hexagon shank
Vehicle dry abrasive paper disc RED PERFECT®
Single wire seal (SEAL) For uninsulated cable connector
Brake/tail light bulb P21/5W Daylight For frequent drivers and drivers who use daytime running lights
Bi-metal blade