ELASTPROOF PW
Coating flexible two-component ELASTPROOF PW
SRFCOAT-2C-(ELASTPROOF-PW)-30KG
Register now and access more than 125,000 products
- Two-component waterproofing mortar made of liquid and powder.
- Impermeable to standing water.
- Suitable for contact with drinking water.
- Excellent adhesion to concrete and mortar.
- Excellent elasticity and flexibility.
- Seals cracks up to 0.6 mm (20º) with a thickness of 2 mm.
- Hardens without cracks.
- Frost- and weather-resistant.
- Certificate of waterproof performance: Laboratori General d'Assaigs i Investigacions (LGAI) exp. no. 94008390.
- Certificate of water potability in contact with Elastproof PW: Laboratorio Dr. Joaquín Riera Tuebols, S.A. exp. no. 4989C.
Do not create partial mixtures of the liquid and powder components.
Do not add water, cement, sand or any other additives that affect the properties of the product.
Precautions for waterproofing water tanks
When waterproofing drinking water tanks, rinse the product 3 or 4 times using plenty of water between days 3 and 28 of the curing period.
Once applied, for at least 3 days, protect the product from weather conditions that may impede curing, such as heavy rain, direct sunlight, excessive heat, wind and frost.
Storage
For 12 months in its original sealed container, stored in a dry place. Protect from frost and excessive heat.
Data acquired at a temperature of +20ºC and a relative humidity of 65 %.
Datasheets(X)
• For waterproofing drinking water tanks.
• For all kinds of water pipes, irrigation channels, wells and ponds.
• When waterproofing swimming pools, the product must be recoated with a protective ceramic coating.
• For structures below the water table.
• For waterproofing basements and garages.
• For waterproofing supports that may sustain or have small deformations or cracks.
• For indoor and outdoor use.
• Preferably apply on the positive side (the side subject to water pressure).
• For creating waterproof coatings on floors that are always covered with a protective element (mortar, tiles etc.).
1. Preparation of the surface
The surface must be clean and firm prior to application of the product.
Oil stains, grease, paint, dust, release agents and cement residues must be removed.
Moisten the surface before applying the product and keep it moist during application. Cracks and holes must be sealed beforehand, create rounded corners at joints.
2. Preparing the paste:
The two components of the product must be mixed together. Pour the liquid component into a clean container and slowly add the powder component while mixing the paste with a mixing drill until a uniform, lump-free paste is formed. If applying the mortar with a brush, 0.6 litres of water needs to be added per set. Wait five minutes and mix again briefly. Do not add to the mortar if the product loses plasticity.
3. Applying the paste:
The product should always be applied with a minimum of 2 coatings with a thickness of between 2 and 3 mm per coating, for a total thickness of 5 mm. Using a trowel or brush, apply the product to the positive side of the support (the side subject to the water pressure. Wait a minimum of three days if other materials have been applied on top of the product.
Colour | Cement grey |
Min. processing temperature | 5 °C |
Max. processing temperature | 30 °C |
Weight of content | 30 kg |
Shelf life from production | 12 Month |
| Technical data | |
| Paste density | Approx. 1.4 g/cm³ |
| Period of workability | 1 hour |
| Mechanically loadable | After approx. 3 days * |
| Waterproof | Approx. 7 days * |
| Contact with drinking water | Approx. 28 days |
| Crack absorption | Up to 0.6 mm * |
| Temperature resistance | -20ºC to +80ºC |
| Waterproof performance | Pressure of 10 atm |
| Application thickness | Between 2 and 5 mm |
| Mixing time | Approx. 5 min. |
| Curing time | Approx. 5 min. |
| Interval between coatings | Minimum 12 hours/maximum 48 hours |
| Loadable with water pressure | Approx. 7 days |
| Can be coated with ceramic | After 3 days |
| Elongation at break | Approx. 100 % |
| Tensile strength | Approx. 1.6 N/mm² |
| * Data acquired at a temperature of +20ºC and a relative humidity of 65 %. | |
Last viewed
M8 reducer attachment
Hand tap, second tap HSS DIN 352
Wire end ferrule with plastic sleeve according to DIN 46228 Part 4
Cross-line laser CLL 18
Multi-purpose drill bit MFD-S Plus
Handle For HDPE service cases
1/2 inch socket wrench insert metric, hexagon, short
1/2 inch socket TX IP
Waterproof coating ISOLPUR PLUS
Quick-mounting system For floor panels