Cement glue MASTERKOL TOPGLUE C2 TE S2
Tile adhesive MASTERKOL TOPGLUE
ADH-TLE-(MASTERKOL TOPGLUE)-20KG
Register now and access more than 125,000 products
Features
- Special formulation that results in a very light adhesive cement with unequalled performance after mixing with water.
- C2 S2 TE rating per EN-12004.
- Does not sag.
- Does not contain silica.
- Includes lightweight aggregates.
- Extended open time and longer ceramic setting time.
Advantages
- Its special formulation facilitates the mixing process, resulting in a creamy paste.
- Higher yield per kg of cement.
Benefits
- Very light, reducing fatigue during application.
- Does not contain silica, protecting the health of the user.
- Requires 30 % less product than a conventional cementitious adhesive.
- Saves costs on transport and logistics.
Do not apply to metal, plastic, PVC, rubber or wood substrates.
Do not apply when bonding artificial stone with a high thermal expansion coefficient to façades or in areas subject to strong sunlight.
Do not apply outside of the permitted temperature range. Do not adjust the original formula. Do not apply outdoors in hot weather without double bonding.
These data are only recommendations based on our experience. Testing prior to use is recommended. For more information, see the product data sheet.
Datasheets(X)
Ideal for natural stone that is particularly sensitive to water. Laying tiles of all formats indoors and outdoors.
Bonding of 1.0 x 3.0 ml SLIM large ceramic sheets or similar, not backed by polyester, for walls and floors. Tiling on façades and exteriors.
Can bond ceramic tiles to plaster supports, plaster, plasterboard, mortar, concrete, prefabricated panels, fibre cement, heated floors and floor overlays.
For heavily used surfaces such as supermarkets, industry, high traffic areas and schools.
For special applications, consult the technical department.
Substrates must be strong, solid, free from paint, wax, oil and grease, and not subject to hydraulic shrinkage. Plaster, plasterboard or derivatives must have a residual moisture level of less than 5 % and be free from dust and efflorescence. Mix 5.8 litres of clean water per 20 kg until homogenised. Use an electric mixer at low speed to prevent lumps. Let stand for 2 minutes and re-mix so the paste is ready for use. Preferably use a toothed trowel, with teeth sized according to size of the tiles. The tiles do not need to be dampened before laying. Lay the tiles with sufficient pressure to ensure at least 80 % contact with the cement. Use the double bonding technique in outdoor areas and on tiles with dovetails. For bonding tiles larger than 30 x 30 cm or 40 kg/m² to façades, also use metal anchors. Constantly use your fingertips to check that a surface layer has not formed. If a surface layer does form, re-comb the cement with the toothed trowel but never soak with water.
Always use pressure on the tile to ensure proper adhesion. Tap the tiles with a rubber club hammer. Protect the newly laid tiles from excessive heat, frost and rain for at least 24 hours after laying.
Storage
For 12 months from the date on the container.
Store in a covered, dry and ventilated place, keeping the product in its sealed container.
Weight of content | 20 kg |
Chemical basis | White cement, sand, additives (polymer modified) |
Standards | EN 12004 |
Colour | White |
Min./max. processing temperature | 5 to 35 °C |
Processing time | 30 min |
Application quantity in weight/area/conditions | 3.8 kg/m² / for 10-mm layer thickness |
May be walked on after max. | 48 h |
May be walked on in following conditions | once completely dry |
Groutable after | 40 min |
Grouting condition | at 20°C and 50% relative humidity |
Full load capacity/conditions | 28 d / at 20°C and 50% relative humidity |
Shelf life from production/conditions | 1 Years / dry, cool and well-ventilated storage, protected against direct sunlight and heat sources |
Last viewed
Chipping hammer MH 10-SE
Cordless hammer drill ABH 18 BASIC
pias® drilling screw with hexagon head and drill tip Case-hardened steel, zinc-plated, blue passivated
Socket contact Micro Quadlok System (MQS) 0.63 Uninsulated
Hexagon Socket Head Cap Screw
Front panel adjuster
Hand pump with hose
BoxBolt® hollow profile fastener
M8 reducer attachment
Plus Quadro-L Vario hammer drill bit